Solar runway lights have moved from emergency stop-gap equipment to a mainstream specification for airfields where grid power is distant, unreliable or simply too expensive to bring to the runway. This guide explains what a solar runway light actually is, which configurations cover a typical airfield, the performance numbers that decide whether a system will work, and the situations where a wired installation is still the right answer.
Why airfields choose solar runway lighting
Conventional runway lighting is a chain of dependencies: a dedicated feeder, a constant-current regulator, series isolation transformers, ducts, pits and trenching along the shoulders. Every one of those elements adds civil works, an approval cycle and a failure point. A solar runway light removes the entire chain. Each fixture carries its own solar panel, battery and controller, so the lighting layout becomes a positioning exercise rather than a construction project.
The practical consequences are significant:
- No trenching — no cutting into shoulders, no ducts to flood, no cable damage from mowers or aircraft.
- No regulator cabinet — nothing to house, cool or protect from humidity.
- Fast deployment — a strip can be lit in days, not months, and the same fixtures can later be relocated to another site.
- Grid independence — lighting keeps working through power outages, which matters for military, remote and emergency operations.
What is inside a solar runway light
A well-built unit is a fully integrated luminaire, not a lamp with a panel bolted on. In the AH-SA-A series, one IP68 die-cast aluminium housing contains the LED head, the driver, the charge controller, the lithium battery and the control electronics. Monocrystalline solar panels are mounted on four sides, so the module averages out partial shading from the head itself and keeps charge input balanced across the day at low latitudes where the sun path is close to overhead. A wireless handheld controller handles switching, intensity and battery monitoring, which means no control cable and no tower link.
The three configurations that cover most airfields
Airfield lighting is defined by position and colour, not by fixture type. A single platform usually covers the whole strip:
| Position | Colour | Beam | Typical model code |
|---|---|---|---|
| Runway edge | White / white (or white / yellow) | Bidirectional | AH-SA-A-RE-WW |
| Runway threshold and end | Red / green | Bidirectional | AH-SA-A-TE-RG |
| Taxiway edge | Blue | Omnidirectional | AH-SA-A-TE-B |
The same platform also covers approach centre-line and crossbar lights, stop bars, aiming point lights, flood lights, and the heliport set — heliport light (red), FATO (white), TLOF (green) and flight path alignment guidance lights.
Performance numbers that decide a specification
Marketing language is unhelpful here; four figures decide whether a solar system will hold up in service.
| Parameter | What to look for |
|---|---|
| Peak intensity | White ≥610 cd, green ≥593 cd, yellow ≥294 cd, red ≥156 cd, blue ≥12 cd |
| Autonomy | 60 h at high intensity bidirectional, 160 h medium, 300 h low |
| Solar input | 20 W monocrystalline (5 W × 4), microprocessor charge regulation |
| Battery | Lithium ion, ≥5 years service life; LiFePO4 where cycle life matters more |
| Ingress protection | IP68 — rated for prolonged immersion, not just rain |
| Wind and temperature | 80 m/s wind speed, -55 to +70 °C, 0-100% RH |
Autonomy is the number most often misread. A 300-hour low-intensity figure is the difference between a system that survives a week of monsoon overcast and one that goes dark on the third night. Ask for the autonomy figure at the intensity level you will actually run, not the best-case value.
Installation reality
A solar airfield lighting installation is mostly a positioning job. Fixtures are set at the specified longitudinal spacing along the runway edges, threshold and end lights go at the strip extremities, and taxiway edge lights follow the connecting taxiway. Each unit sits on its mounting base — 200 × 200 mm on M10 studs — and is levelled in place. Where aircraft can strike the fixture, a frangible coupling base is specified so the light breaks away instead of damaging the airframe.
Commissioning is done fixture by fixture through the wireless remote controller: intensity mode, steady or flashing operation, and on/off state. The same controller reports battery status, which turns routine inspection into a walk-through rather than a teardown.
When wired lighting is still the better choice
Solar is the wrong answer in three cases: a high-category precision approach runway with demanding intensity and switching requirements, sites where sun hours are genuinely insufficient in winter, and airports that require full ATC-controlled dimming and monitoring across the entire system. In those cases a wired installation with series circuits remains the standard. For regional airfields, military and expeditionary strips, helipads, temporary or emergency operating surfaces and remote airstrips, solar is now the more economical and faster route to compliance.
Compliance checklist before you buy
- ICAO Annex 14 Volume I (9th Edition, July 2022) — aerodrome design and operations
- ICAO Annex 14 Volume II — heliports, including FATO and TLOF lighting
- FAA AC 150/5345-50B — specification for portable runway and taxiway lights
- Documented photometric test data per colour, not just a generic intensity claim
- IP68 certification with immersion test evidence, plus stated wind speed rating
Frequently asked questions
How long do the batteries last? Rated service life is five years or more. Ask whether the pack is field-replaceable — it should be, since the LED head will outlast two or three battery generations.
Can the lights be synchronized? Yes. GPS synchronization is available so fixtures flash in phase without any interconnect cable.
Can they run on AC where power exists? An external AC charger (110-240 V) is available as an option, giving a hybrid mode for hangars and aprons.
Are they visible with night vision goggles? IR LED versions are available for military use.
Bottom line
A solar runway light system replaces trenching, cable and regulators with distributed energy storage and a remote controller. Specify it by autonomy at operating intensity, IP rating, wind rating and documented photometric performance — and match the fixture configuration to the position on the airfield rather than to a catalogue photograph. For remote, temporary and military airfields, that combination delivers code-compliant lighting in a fraction of the time and cost of a wired installation.